View LTW-42NDP3ZT-012A_8963292.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on dcc release bns-od-fc001/a4 lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTW-42NDP3ZT-012A spec no. :ds20-2017-0002effective date: 02/03/2017 revision: a
1 / 11 part no. : lt w - 42nd p3z t - 0 1 2a bns-od-fc002/a4 through hole lamp LTW-42NDP3ZT-012A through hole lamp LTW-42NDP3ZT-012A rev description by date p001 preliminary spec (rdr-20161257-02) norah 10/17 /2016 p002 update p/n norah 10/24/2016 above data for pd and customer tracking only - nppr received and upload on opnc sasipan 01/13/2017
2 / 11 part no. : lt w - 42nd p3z t - 0 1 2a bns-od-fc002/a4 through hole lamp LTW-42NDP3ZT-012A 1. description through hole white leds are offered in a variety of package s such as 3mm, 4mm, 5mm, rectangular and cylinder w hich are suitable for all applications requiring status indi cation. sever al intensity and viewing angle choices are availabl e in each package for design flexibility. 1. 1. features lead (pb) free product - rohs compliant low power consumption & high efficiency. versatile mounting on p.c. board or panel. i.c. compatible/low current requirement. popular t-1 diameter ingan white & water clear lens esd protected 1.2. applications computer communication consumer home appliance industrial 2. outline dimensions notes : 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm (.010") unless otherwise noted . 3. protruded resin under flange is 1.0mm (.04") max. 4. lead spacing is measured where the leads emerge fro m the package. 5. specifications are subject to change without notice . protection circuit protection zener led
3 / 11 part no. : lt w - 42nd p3z t - 0 1 2a bns-od-fc002/a4 through hole lamp LTW-42NDP3ZT-012A 3. absolute maximum ratings at ta=25 parameter maximum rating unit power dissipation 100 mw peak forward current (duty cycle Q 1/10, pulse width Q 10ms) 100 ma dc forward current 30 ma derating linear from 30 0.45 ma/ electrostatic discharge 5000v operating temperature range -40c to + 85c storage temperature range -40c to + 100c lead soldering temperature [2.0mm (.079") from body] 260c for 5 seconds max. 4. electrical / optical characteristics at ta=25 parameter symbol min. typ. max. unit test condition luminous intensity iv 565 - 1425 mcd if = 2ma note 1,3,4 viewing angle 2 1/2 - 30 - deg note 2 (fig.6) chromaticity coordinates x - 0.28 - nm if = 2ma, note 5 hue spec. table & chromaticity diagram y - 0.30 - nm forward voltage vf 2.5 2.65 2.8 v if = 2ma reverse current ir - - 1 a vr = 5v note: 1. luminous intensity is measured with a light sens or and filter combination that approximates the cie eye-response curve. 2. 1/2 is the off-axis angle at which the luminous int ensity is half the axial luminous intensity. 3. iv classification code is marked on each packing bag. 4. the iv guarantee must be included with 10% test ing tolerance. 5. the chromaticity coordinates (x, y) is derived f rom the 1931 cie chromaticity diagram.. 6. reverse voltage (vr) condition is applied for ir test only. the device is not designed for reverse operation.
4 / 11 part no. : lt w - 42nd p3z t - 0 1 2a bns-od-fc002/a4 through hole lamp LTW-42NDP3ZT-012A 5. typical electrical / optical characteristics cur ves (25 ambient temperature unless otherwise noted)
5 / 11 part no. : lt w - 42nd p3z t - 0 1 2a bns-od-fc002/a4 through hole lamp LTW-42NDP3ZT-012A 6. taping features * compatible with radial lead automatic insertion e quipment. * most radial lead plastic lead lamps available pac kaged in tape and folding. * 2.54mm (0.1") straight lead spacing available. * folding packaging simplifies handling and testing . * reel packaging is available by removing suffix a on option. * ammo packing series lamp type 24 led+gap. package dimensions specification item symbol minimum maximum mm inch mm inch tape feed hole diameter d 3.8 0.149 4.2 0.165 component lead pitch f 2.3 0.091 3.0 0.118 front to rear deflection h -- -- 2.0 0.078 feed hole to bottom of component h1 21.5 0.846 22.5 0.886 feed hole to overall component height h2 25.7 1.012 27.2 1.071 lead length after component height l w0 11.0 0.433 feed hole pitch p 12.4 0.488 13.0 0.511 lead location p1 4.4 0.173 5.8 0.228 center of component location p2 5.05 0.198 7.65 0.301 total tape thickness t -- -- 0.90 0.035 feed hole location w0 8.5 0.334 9.75 0.384 adhesive tape position w2 0 0 3.0 0.118 tape width w3 17.5 0.689 19.0 0.748
6 / 11 part no. : lt w - 42nd p3z t - 0 1 2a bns-od-fc002/a4 through hole lamp LTW-42NDP3ZT-012A 7. packing spec. 3000 pcs per packing bag 10 inner cartons per outer carton total 30,000 pcs per outer carton in every shipping lot, only the last pack will be non-full packing
7 / 11 part no. : lt w - 42nd p3z t - 0 1 2a bns-od-fc002/a4 through hole lamp LTW-42NDP3ZT-012A 8. bin table specification luminous intensity iv (mcd) if@ 2 ma bin code min. max. g 565 715 h 715 900 j 900 1125 k 1125 1425 note: tolerance of each bin limit is 10% forward voltage vf ( v ) if@2 ma bin code min. max. 1 2.5 2.6 2 2.6 2.7 3 2.7 2.8 note: forward voltage measurement allowance is 0.0 5v hue ranks chromaticity coordina tes, cc(x, y), if@2ma a0-11 x 0.2720 0.2640 0.2699 0.2772 y 0.2580 0.2670 0.2771 0.2690 a0-12 x 0.2772 0.2699 0.2758 0.2824 y 0.2690 0.2771 0.2872 0.2784 a0-31 x 0.2640 0.2575 0.2638 0.2699 y 0.2670 0.2743 0.2850 0.2771 a0-32 x 0.2699 0.2638 0.27 01 0.2758 y 0.2771 0.2850 0.2970 0.2872 a0-21 x 0.2824 0.2758 0.2821 0.2876 y 0.2784 0.2872 0.2979 0.2878 a0-22 x 0.2876 0.2821 0.2880 0.2928 y 0.2878 0.2979 0.3080 0.2972 a0-41 x 0.2758 0.2701 0.2763 0.2821 y 0.2872 0.2970 0.3090 0.2979 a0-42 x 0.2821 0.2763 0.2826 0.2880 y 0.2979 0.3090 0.3190 0.3080 b3-1 x 0.2928 0.2880 0.2939 0.2980 y 0.2972 0.3080 0.3181 0.3066 b3-3 x 0.2880 0.2826 0.2889 0.2939 y 0.3080 0.3190 0.3280 0.3181 note: color coordinates measurement allowance is 0 .01
8 / 11 part no. : lt w - 42nd p3z t - 0 1 2a bns-od-fc002/a4 through hole lamp LTW-42NDP3ZT-012A c.i.e. 1931 chromaticity diagram
9 / 11 part no. : lt w - 42nd p3z t - 0 1 2a bns-od-fc002/a4 through hole lamp LTW-42NDP3ZT-012A 9. cautions 9.1. application this led lamp is good for application of indoor and outdoor sign, also ordinary electronic equipment. 9.2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is re commended that leds out of their original packaging are used withi n three months. for extended storage out of their o riginal packaging, it is recommended that the leds be stored in a sealed con tainer with appropriate desiccant or in desiccators with nitrogen ambient. 9.3. cleaning use alcohol-based cleaning solvents such as isoprop yl alcohol to clean the leds if necessary. 9.4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do no t use the base of the lead frame as a fulcrum during forming. lead formin g must be done before soldering, at normal temperat ure. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 9.5. soldering when soldering, leave a minimum of 2mm clearance fr om the base of the lens to the soldering point. dip ping the lens into the solder must be avoided. do not apply any external s tress to the lead frame during soldering while the led is at high temperature. recommended soldering conditions: soldering iron wave soldering temperature soldering time position 350c max. 3 seconds max. (one time only) no closer than 2mm from the base of the epoxy bulb pre-heat pre-heat time solder wave soldering time dipping position 100c max. 60 seconds max. 260c max. 5 seconds max. no lower than 2mm from the base of the epoxy bulb note: excessive soldering temperature and/or time m ight result in deformation of the led lens or catas trophic failure of the led. ir reflow is not suitable proce ss for through hole type led lamp product. 9.6. drive method an led is a current-operated device. in order to en sure intensity uniformity on multiple leds connecte d in parallel in an application, it is recommended that a current limit ing resistor be incorporated in the drive circuit, in series with each led as shown in circuit a below. circuit model (a) circuit model (b) led led (a) recommended circuit (b) the brightness of each led might appear differe nt due to the differences in the i-v characteristic s of those leds.
10 / 11 part no. : lt w - 42nd p3z t - 0 1 2a bns-od-fc002/a4 through hole lamp LTW-42NDP3ZT-012A 9.7. esd (electrostatic discharge) static electricity or power surge will damage the l ed. suggestions to prevent esd damage: use a conductive wrist band or anti- electrostatic glove when handling these leds all devices, equipment, and machinery must be prop erly grounded work tables, storage racks, etc. should be properl y grounded use ion blower to neutralize the static charge whi ch might have built up on surface of the leds plast ic lens as a result of friction between leds during st orage and handing suggested checking list: training and certification 9.7.1.1. everyone working in a static-safe area is esd-certified? 9.7.1.2. training records kept and re-certific ation dates monitored? static-safe workstation & work areas 9.7.2.1. static-safe workstation or work-areas have esd signs? 9.7.2.2. all surfaces and objects at all stati c-safe workstation and within 1 ft measure less tha n 100v? 9.7.2.3. all ionizer activated, positioned toward s the units? 9.7.2.4. each work surface mats grounding is g ood? personnel grounding 9.7.3.1. every person (including visitors) han dling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 9.7.3.1. if conductive footwear used, conductive flooring also present where operator stand or walk? 9.7.3.2. garments, hairs or anything closer th an 1 ft to esd items measure less than 100v*? 9.7.3.3. every wrist strap or heel strap/condu ctive shoes checked daily and result recorded for a ll dls? 9.7.3.4. all wrist strap or heel strap checker s calibration up to date? note: *50v for blue led. device handling 9.7.4.1. every esds items identified by eia-47 1 labels on item or packaging? 9.7.4.2. all esds items completely inside prop erly closed static-shielding containers when not at static-safe workstation? 9.7.4.3. no static charge generators (e.g. pla stics) inside shielding containers with esds items? 9.7.4.4. all flexible conductive and dissipati ve package materials inspected before reuse or recy cle? others 9.7.5.1. audit result reported to entity esd co ntrol coordinator? 9.7.5.2. corrective action from previous audit s completed? 9.7.5.3. are audit records complete and on file ?
11 / 11 part no. : lt w - 42nd p3z t - 0 1 2a bns-od-fc002/a4 through hole lamp LTW-42NDP3ZT-012A 10. reliability test classification test item test condition sample size reference standard endurance test operation life ta = under room temperature if = per data sheet maximum rating test time= 1000hrs 22 pcs (cl=90%; ltpd=10%) mil-std-750d:1026 (1995) mil-std-883g:1005 (2006) high temperature high humidity storage (thb) ta = 60c rh = 90% test time= 240hrs 22 pcs (cl=90%; ltpd=10%) mil-std-202g:103b (2002) jeita ed-4701:100 103 (2001) high temperature storage ta= 105 5c test time= 1000hrs 22 pcs (cl=90%; ltpd=10%) mil-std-750d:1031 (1995) mil-std-883g:1008 (2006) jeita ed-4701:200 201 (2001) low temperature storage ta= -55 5c test time= 1000hrs 22 pcs (cl=90%; ltpd=10%) jeita ed-4701:200 202 (2001) environmental test temperature cycling 100c 25c -40c 25c 30mins 5mins 30mins 5mins test time: 30 cycles 22 pcs (cl=90%; ltpd=10%) mil-std-750d:1051 (1995) mil-std-883g:1010 (2006) jeita ed-4701:100 105 (2001) jesd22-a104c (2005) thermal shock 100 5c -30c 5c 15mins 15mins test time: 30 cycles 22 pcs (cl=90%; ltpd=10%) mil-std-750d:1056 (1995) mil-std-883g:1011 (2006) mil-std-202g:107g (2002) jesd22-a106b (2004) solder resistance t.sol = 260 5c dwell time= 101 seconds 2mm from the base of the epoxy bulb 11 pcs (cl=90%; ltpd=18.9%) mil-std-750d:2031(1995) jeita ed-4701: 300 302 (2001) solderability t. sol = 245 5c dwell time= 5 0.5 seconds (lead free solder, coverage R 95% of the dipped surface) 11 pcs (cl=90%; ltpd=18.9%) mil-std-750d:2026 (1995) mil-std-883g:2003 (2006) mil-std-202g:208h (2002) ipc/eia j-std-002 (2004) soldering iron t. sol = 350 5c dwell time= 3.5 0.5 seconds 11 pcs (cl=90%; ltpd=18.9%) mil-std-202g:208h (2002) jeita ed-4701:300 302 (2001) 11. others white led is materialized by combining blue led and phosphors. color of white led is changed a litt le by an operating current. the appearance and specifications of the product ma y be modified for improvement, without prior notice .

▲Up To Search▲

Price & Availability of LTW-42NDP3ZT-012A

	To Download LTW-42NDP3ZT-012A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .